The KIN-TEK Analytical FlexStream™ Gas Standard Generator System is composed of one or more modules, depending on application requirements.
FlexStream™ Modules can be packaged in stand-alone carrying cases or packaged in one or two 3-module expansion cases. Unused module slots in the expansion cases are filled with blank panels. The modules are electronically connected to each other by a short cable on the rear panel.
FlexStream™ Base Module (FlexBase)
The “Base” module is required in every FlexStream™ system. This module provides:
- Front panel color touchscreen
- Permeation tube oven
- Primary dilution mass flow rate
- Ethernet and serial RS-232 connectivity to an external computer
FlexBase™ Gas Standards Generator Base Module Brochure
FlexBase™ Gas Standards Generator Base Module Specifications
FlexStream™ Auxiliary Permeation Oven Module (FlexPM)
The “Additional permeation tube ovens allow generation of a multi-component gas stream for cases in which;
- tubes must be maintained at different temperatures
- differing permeation technologies (disposable tubes vs. refillable tubes) are required
- more components are needed than can be held in a single oven, or
- for applications in which various components will be switched in and out of the gas stream.
Up to 5 PM oven modules can be added wherein each oven can hold up to eight disposable permeation tubes or one factory-refillable tube. An added benefit is that any combination of ovens can be kept on standby to keep various tubes at temperature while not adding their emission to the output gas stream.
FlexPM™ Auxiliary Permeation Oven Module Brochure
FlexPM™ Auxiliary Permeation Oven Module Specification
FlexStream™ Gas Feed Permeation Oven Module (FlexPM/GF)
Most applications can use liquid-filled permeation tubes. However, some compounds (e.g., NO, CO, O2, etc.) have very high vapor pressures and require a special mechanism to achieve desired concentration levels. The FlexPM/GF Module contains the same oven as an auxiliary Permeation Oven Module (PM) but with additional controls that allow the customer to refill a “customer-refillable” gas-fed permeation tube and to set the operating pressure of the tube. These are special tubes, typically made of stainless steel. Prior to shipment, KIN-TEK determines the certified emission rate of the gas fed tube for one or more components. In use, the customer typically supplies the pure component gas from their cylinder to initially fill the tube and to periodically recharge/refill it.
FlexGF™ Gas Feed Permeation Oven Module Brochure
FlexGF™ Gas Feed Permeation Oven Module Specifications
FlexStream™ Secondary Dilution Module (FlexSD)
The FlexSD module extends the concentration range attained from permeation tubes by providing an additional stage of dilution of the primary gas stream. Very low concentrations – ppb or ppt – can be generated depending on the emission rate of the tubes and the flow rate range of the primary and secondary dilution mass flow controllers. Overall dilution ratios of 10,000:1 can be achieved.
FlexSD™ Secondary Dilution Module Brochure
FlexSD™ Secondary Dilution Module Specifications
FlexStream™ Humidification Module (FlexHG)
Many applications require the calibration gas standard to simulate “real world” conditions including the presence of humidity. The FlexHG is used to add humidity to a standard gas stream. The computer system automatically adjusts flows to maintain %RH at varying total flows, or adjusts to change %RH as required. The trace concentration mixture does not contact liquid water. The HG module is operated from the Base Module touchscreen.
FlexHG™ Humidification Module Brochure
FlexHG™ Humidification Module Specifications
FlexStream™ Interface Module (FlexIM)
The Interface Module (FlexIM) contains gas stream interfacing components needed to assure constant gas stream output conditions independent of variations in flow and pressure. The Interface Module is ideal for applications where flow capacity of end use is limited (e.g., filling of gas bags), or when back pressure is required to introduce the output gas stream sample to the device under test. Controls are provided on the front panel for adjusting the output pressure.
FlexIM™ Interface Module Brochure
FlexIM™ Interface Module Specifications
